ckochandClaude Opus 5.5
1400cc8afd
- KiCad project generated by pcb/tools (design, route, schematic, fab outputs). - v0.4 fixes the v0.3 review findings: low-dropout 3.3 V regulator, OR'd 5 V supply, polyfuse, USB ESD protection, input clamps, ceramic decoupling at the drivers, A4988/DRV8825 jumper, ground stitching. DRC/ERC clean. - v0.3 (as ordered) kept in pcb/archive/v0.3. - FluidNC config.yaml for the board; rho hard limit on. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
99 lines
6.3 KiB
Markdown
99 lines
6.3 KiB
Markdown
# SandTable Controller v0.3 (custom PCB)
|
||
|
||
|
||
|
||
A 2-layer, 80 × 63 mm board that replaces the Arduino Uno + CNC shield in the sand table. It uses the **same 4 mounting holes as an Uno**, so it fits the deck standoffs.
|
||
|
||
**Status: designed and checked in KiCad, with order files ready for PCBWay. It has not been built or tested yet.**
|
||
|
||
- **MCU:** ESP32-WROOM-32E (Wi-Fi), running FluidNC. USB-C programming through a CH340C with auto-reset, so no buttons need pressing.
|
||
- **Motors:** 2× DRV8825 StepStick sockets, with 100 µF bulk capacitors. The board fixes the drivers at 1/32 microstepping and keeps them awake: M0–M2, RESET and SLEEP are all tied to 3.3 V. A4988 drivers also fit and run at 1/16.
|
||
- **Power:** 12 V barrel jack with a reverse-polarity diode → RECOM R-78E 5 V switching regulator → AMS1117 3.3 V. USB 5 V and regulator 5 V are diode-ORed, so USB alone powers the logic for flashing. The motors need the 12 V supply.
|
||
- **Connectors:** JST-XH to match the motor cable plugs:
|
||
- 2× motor
|
||
- home switch
|
||
- hall sensor (5 V)
|
||
- WS2812B LED data (buffered to 5 V)
|
||
- 4-pin expansion header
|
||
- **Copper:** ground pour on both layers. The ESP32 antenna sits over a copper-free area at the board edge.
|
||
|
||
## Changes in v0.3
|
||
- **No holes in solder pads.** PCBWay's review of v0.2 found vias inside pads, which they would only build reliably by filling them with resin, for extra cost.
|
||
- The router now keeps every via at least 0.2 mm from every pad. In v0.2, 26 vias sat in or overlapped pads of small parts.
|
||
- The ESP32's 12 ground-pad holes are replaced by one solid copper pad, with the same 9 solder windows.
|
||
- PCBWay can now build it as drawn, with no via filling.
|
||
- **Parts list:** exact part numbers for the 4-pin header (Sullins PRPC004SAAN-RC), the driver sockets (Sullins PPTC081LFBN-RC) and the 100 µF capacitors (Panasonic EEE-FK1V101GP), as agreed with PCBWay.
|
||
|
||
## Changes in v0.2
|
||
- **Drivers:** DRV8825 instead of TMC2209 in UART mode. The serial line and its resistor are removed, so IO16/IO17 are now free.
|
||
- **Holes:** the smallest hole is now 0.3 mm. The ESP32 footprint's 0.2 mm ground-pad vias were enlarged, because PCBWay charges extra for holes under 0.3 mm.
|
||
- **Order files:** a PCBWay order folder (Gerbers, parts list, placement file, assembly drawing, order sheet) replaces the JLCPCB files.
|
||
- **Silkscreen:** VMOT / EN / DIR are printed beside each driver socket.
|
||
|
||
## Checks (KiCad 9.0.7, `kicad-cli`)
|
||
|
||
| Check | Result |
|
||
|---|---|
|
||
| ERC (schematic) | 0 violations |
|
||
| DRC (board, all severities) against PCBWay's standard limits: 6/6 mil trace/space, 0.3 mm hole, 0.15 mm ring | 0 violations, 0 unconnected |
|
||
| Schematic ↔ PCB parity | 0 differences |
|
||
| Vias within 0.2 mm of a pad, holes inside a pad (checked from the board file) | 0 |
|
||
|
||
## Ordering from PCBWay
|
||
Everything for the order is in [`pcbway-order/`](pcbway-order/). [`ORDER.md`](pcbway-order/ORDER.md) there lists the exact settings to enter, which file goes in which upload box, and a note to paste for PCBWay.
|
||
|
||
| File | What |
|
||
|---|---|
|
||
| `1-gerbers-…zip` | Board files: Gerbers plus separate plated and non-plated drill files |
|
||
| `2-bom-…csv` | Parts list for turnkey assembly, with manufacturer part numbers |
|
||
| `3-centroid-…csv` | Part positions in mm, origin at the board's bottom-left corner |
|
||
| `assembly-top-…pdf`, `schematic-…pdf` | For PCBWay's engineers if they ask |
|
||
|
||
The DRV8825 modules are not on the order; you plug in your own. The back of the board has PCBWay's "WayWayWay" marker, so their order number prints there instead of on the front.
|
||
|
||
## Before first power-up
|
||
1. **Driver direction.** Line up the module's VMOT, EN and DIR pins with the VMOT / EN / DIR labels on the board. A driver plugged in backwards is destroyed.
|
||
2. **Driver current.** On a DRV8825, current limit = 2 × Vref (with the usual 0.1 Ω sense resistors).
|
||
- Start at about 70 % of the motor's rated current. For example, a 1.0 A motor needs Vref ≈ 0.35 V.
|
||
- Measure Vref between the trim pot and GND with the 12 V supply connected.
|
||
- Never plug or unplug a motor while the power is on.
|
||
3. **Home switch wiring.** Connect the switch's COM to HOME pin 3 (GND) and its NO contact to pin 2.
|
||
4. **Firmware.**
|
||
- Flash FluidNC over USB with the FluidNC web installer.
|
||
- Upload `fluidnc/config.yaml` as `config.yaml`.
|
||
- In the config, X is theta in degrees and Y is rho in mm. `$H` homes rho.
|
||
- If an axis turns the wrong way, add `:low` to its direction pin.
|
||
|
||
## ESP32 pin map
|
||
|
||
| Function | GPIO |
|
||
|---|---|
|
||
| Theta (spin) STEP / DIR | IO18 / IO19 |
|
||
| Rho (arm) STEP / DIR | IO27 / IO14 |
|
||
| Driver enable (shared, low = on, pulled up so the drivers are off at boot) | IO13 |
|
||
| Rho home switch | IO34 |
|
||
| Theta hall sensor | IO35 |
|
||
| LED strip data (through a 74AHCT1G125 buffer) | IO33 |
|
||
| Status LED | IO2 |
|
||
| Expansion header | IO32, IO25 |
|
||
| Free, not connected | IO16, IO17 |
|
||
|
||
## Files
|
||
|
||
| Path | What |
|
||
|---|---|
|
||
| `kicad/` | KiCad 9 project: schematic, board, and project-local symbol and footprint tables |
|
||
| `sandtable-controller-schematic.pdf` | Schematic |
|
||
| `pcbway-order/` | Everything to upload to PCBWay, plus `ORDER.md` with the settings |
|
||
| `renders/` | 3D renders |
|
||
| `sandtable-controller.step` | 3D model. The copy placed in `sand-table-v2.solidcraft` is v0.1, which has the same outline and holes. |
|
||
| `fluidnc/config.yaml` | FluidNC machine config (a starting point, not yet run on hardware) |
|
||
| `tools/` | Python generator: `design.py` (parts, placement, nets, sourcing) → `route.py` (router, ground pour, board file), `sch.py` (schematic), `fab.py` (PCBWay order folder, renders, copy into this folder) |
|
||
|
||
To regenerate everything, run `python3 tools/route.py && python3 tools/sch.py && python3 tools/fab.py`. The KiCad files are built in `~/kicad/sandtable-controller` because the KiCad snap can't read inside `~/snap/`.
|
||
|
||
## Notes
|
||
- **5 V budget:** the 5 V regulator supplies 0.5 A. That covers the ESP32 plus a short LED strip (about 10 LEDs at full white). Use a separate 5 V supply for longer strips.
|
||
- **Noise:** DRV8825s are louder than TMC2209s; expect some motor whine. TMC2209 modules in standalone mode might work in these sockets, but their pin layouts vary by brand, so check before trying one.
|
||
- **LED strip:** FluidNC doesn't drive the WS2812B header. It's there for other firmware or an add-on later.
|